plc training courses
Siemens S5  |  Siemens LOGO / S7 200  |  Siemens S7 300 / 400  |  Siemens S7 1200 / 1500  |  Siemens WinCC HMI/SCADA  |  Siemens Networks  |  Allen Bradley / Rockwell  |  Allen Bradley Networks/HMIs  |  Mitsubishi  |  Omron  |  GE Fanuc  |  Prosoft  |  Invensys Wonderware www.plc-training.co.uk HomeContact
plc training courses
plc training courses PLC Training Courses
Main Menu
Home Home
PLC Training Courses PLC Training Courses
Latest Dates & Prices Latest Dates & Prices
EAL Accreditation EAL Accreditation
Forces Resettlement Forces Resettlement
Emergency PLC Support Emergency PLC Support
Software Support Software Support
Automation Spares Automation Spares
Our Customers Our Customers
Customer Feedback Customer Feedback
Special Discounts Special Discounts
One to One Training One to One Training
Accommodation Accommodation
Booking Terms Booking Terms
Make a Payment Make a Payment
Contact Us Contact Us
 
PLC Types
Siemens S7 300 / 400 PLC Siemens S7 300 / 400 PLC
Siemens S7 1200 Siemens S7 1200
Allen Bradley ControlLogix Allen Bradley ControlLogix
Allen Bradley CompactLogix Allen Bradley CompactLogix
Allen Bradley FlexLogix Allen Bradley FlexLogix
Siemens S7 200 PLC Siemens S7 200 PLC
Allen Bradley SLC500 PLC Allen Bradley SLC500 PLC
Siemens S5 100/115 PLC Siemens S5 100/115 PLC
Siemens S5 135/155 PLC Siemens S5 135/155 PLC
Mitsubishi FX Series PLC Mitsubishi FX Series PLC
Siemens Logo Siemens Logo
Mitsubishi A Series PLC Mitsubishi A Series PLC
Mitsubsihi Q Series PLC Mitsubsihi Q Series PLC
Omron C Series PLC Omron C Series PLC
Allen Bradley PLC5 PLC Allen Bradley PLC5 PLC
Prosoft Prosoft
 
Course Categories
PLC Troubleshooting PLC Troubleshooting
EAL L3 Accredited EAL L3 Accredited
HMI Courses HMI Courses
SCADA SCADA
Network Courses Network Courses
 
Software
Allen Bradley Allen Bradley
Siemens Siemens
Siemens TIA Portal Siemens TIA Portal
Simatic Manager Simatic Manager
MicroWin V4.0 MicroWin V4.0
WinCC WinCC
RSLogix 500 RSLogix 500
RSLogix 5000 RSLogix 5000
RSView RSView
GX Developer GX Developer
IEC GX Developer IEC GX Developer
Wonderware Wonderware
RSNetworx DeviceNet RSNetworx DeviceNet
CX Developer / CX One CX Developer / CX One
DOS Based Step 5 DOS Based Step 5
Mitsubishi Epanel Mitsubishi Epanel
Mitsubishi GT Designer Mitsubishi GT Designer
Mitsubishi IQ Works Mitsubishi IQ Works
RSLogix 5 RSLogix 5
Siemens Logo Siemens Logo
Prosoft Prosoft
PanelBuilder 32 PanelBuilder 32
Cimplicity Cimplicity
 
plc training courses
plc training courses
plc training courses
plc training courses plc training courses plc training courses
Search:
plc training courses
plc training courses
Mitsubishi FX, A and Q Series PLC Level 1 IEC Thursday Feb 22nd, 2018
plc training courses
plc training courses
 

PLC Training Course:
Download the Mitsubishi FX, A and Q Series PLC Level 1 IEC
course as a PDF document

Course Title Mitsubishi FX, A and Q Series PLC Level 1 IEC
Software IEC GX Developer
PLC-Type Mitsubsihi Q Series PLC
Duration 5 days
Pre-Requisites No prerequisites this is a beginners course
Maximum Delegates 6
Prices Click here for prices

Brief Description
  • Be able to recognise Mitsubishi FX , A and Q Series hardware and be able to locate and cure most faults that occur.
  • Be able to operate the IEC GX Developer software to make it perform certain tasks.
  • Understand basic FX, A and Q Series instruction set and be able to make minor modifications to software.
  • Be able to backup and restore a PLC program when required.
  • Be able to perform basic system diagnostics when a problem occurs.

Course Documentation
  • Beginners guide to IEC GX Developer
    PLC Training - Mitsubishi FX, A and Q Series PLC Level 1 IEC
       
    Course Content
    To fault find a system you need to know EXACTLY how it works
     
    HOW EXACTLY DOES A PLC WORK?
    • Am I getting the input to the PLC?
    • The Led on the output card means i am getting voltage out right? does it?
    • What exactly happens in between? ,theres more than just a program in the CPU
    • How exactly does it scan the program?
    • What is this Watchdog Timer? Is it that important?
    • Can I use the same output twice? That's bad programming isn't it?
    • A PLC is a logic controller, so use a logical approach to fault find it.
    • What are the 8 simple test points to check?
    • The PLC is in RUN, that means theres a program right? does it?
    • FORCING a bit and toggling a bit is pretty much the same yeah? depends on which PLC

    Then you need to Know the specifics

     
    HOW DO I DO THE FOLLOWING?

    (some straight forward some not so)

    • How do I check power is ON and PLC is in right mode (RUN or Program)
    • Check for a fault condition
    • Establish a link between PC and PLC (can be a major issue nowadays)
    • If comms problem check interface
    • Create a blank project and take a backup (just in case I mess up)
    • Open project for PLC and go OnLine
    • Interrogate Diagnostics
    • Identify if it is a hardware or software fault?
    • Change the battery
    • Change modules if necessary, (with spares and without spares)
    • Identify if it is a PLC or Comms fault
    • Check all settings against a template etc.
    • Check Hardware ( What voltage should be where)
    • Clear Memory and Download program
    • Check software against latest copy
    • Monitor program effectively
    • Searching for specific operands and instructions
    • Changing timer, counter values On Line
    • Making minor mods Off Line and On line
    • Check or create a monitor table to establish parameter status  
    • Call up reference data to assist with software diagnostics
    • Display Documentation (Symbols, Comments)
    • Reassign an I/O address and change software addresses
    • Printing Cross Reference / Program Listings etc.
    • Intermediate Instructions
    • Jumps, Subroutines
    • Linking via EtherNet
    • PLC to PLC Comms
    • Linking to HMIs
    • Remote IO via CClink

    Background information also covered

    Understanding of the following:

    • Number formats, bits, bytes, words, double words
    • Binary, HEX,octal,floating point, integer
    • Data types and parameter types, Bool etc.
    • On Line and Off Line modes
    • Basic Instructions, contacts, Set, reset etc.
    • Timers, Counters
    • Comparators, Maths
    • How to make minor mods
    • Altering values in a monitor table
    • Using Device Monitor function
    • Back tracking through a program to establish where power flow stops
    • Reset procedure
    • Fault finding tips
     
    Course Equipment Per Delegate
    • FX, A or Q series PLC
    • PC or Laptop
    • Simulator
       

      plc training courses
      plc training courses   plc training courses
      plc training courses   plc training courses
        © Equinox PLC Training Solutions 2018  
        A FedWeb Site